Timing Belt Replacement - Mitsubishi-Forums.com
 
LinkBack Thread Tools
post #1 of 15 (permalink) Old 08-15-2006, 08:10 AM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
Hi,
I need to replace my timing belt, i already did this before in other cars.
the problem is, the colt crankshaft pully doesn´t has holes to hold it.
How can i hold the crankshaft pully to remove the bolt??
thanks

Paulo Lança
Paulo Lanca is offline  
Sponsored Links
Advertisement
 
post #2 of 15 (permalink) Old 08-15-2006, 08:21 AM
Senior
 
Join Date: Jun 2006
Posts: 500
Send a message via Yahoo to conanofcimmeria
the honest reply is to put a 1/2 drive socket on it with a breaker bar and hit the starter(not to start only to bump).this is a common way and we use it all the time on the l200 trucks.if that disturbs you then try putting the vehicle in gear and have someone step on the brakes very hard.you should be able to loosen the bolt this way as well.
conanofcimmeria is offline  
post #3 of 15 (permalink) Old 08-15-2006, 09:50 AM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
Jesus!!!!
i believe you, but after reading you solution , gave me an idea.
I have a small air compressor (130psi) and i was thinking maybe buying a pneumatic impact wrench? what do you think? will be usefull?
or you think its a waste of money?
thanks

Paulo Lança
Paulo Lanca is offline  
post #4 of 15 (permalink) Old 08-15-2006, 12:14 PM
Senior
 
Join Date: Jun 2006
Posts: 500
Send a message via Yahoo to conanofcimmeria
air tools of any kind are never wasted money.you may find that you will need to undo the motor mount and support the engine on a floor jack to raise/lower the engine to get access to the crank bolt.many times you need to undo the mount anyway to get the belt off and on depending on the engine you have
conanofcimmeria is offline  
post #5 of 15 (permalink) Old 08-15-2006, 07:57 PM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
ok, thanks
I´ll try the your way first, i´ll keep in touch.

Paulo Lança
Paulo Lanca is offline  
post #6 of 15 (permalink) Old 08-16-2006, 08:46 AM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
Its done, i used the 1/2 drive socket on it with a breaker bar, like you said, but i had to bump the engine four times before the bolt got lose.
(at the begining i has afraid, but everything went ok)
Yes its true, Now i need to undo the mount anyway to get the belt off.
i´m gonna do it this afternoon.
To put the ckanshaft bolt again, i have to used the drive socket with a breaker bar again?
Regards

Paulo Lança
Paulo Lanca is offline  
post #7 of 15 (permalink) Old 08-16-2006, 11:46 AM
Member
 
Join Date: Feb 2005
Posts: 37
Yes you can use the breaker bar but make sure you get that crank pully bolt tightened to spec or its will come lose and damage the key and the crank pully and the lower timing sproket as well being lose that long the key walowed out the keyways on the crank pully and the lower timing sproket so I could not set the timing as there was about 5 degs of play in the lower sproket due to the key eating it all up inside was a big mess but its all fixed now the key is one hard part to find so you do not want it messed up.

I used a big screw driver to hold the pully shoved it trough one of the open areas of the crank pully to hold it from turnning just make sure screwdriver is a strong one that will not break or bend and dont use the plastic timing cover as a place to wedge the srewdriver as it will break the cover duriing the force of tighting up the pully and you will neeed someone to help hole the screwdriver in place when your tighting up the pully. there is a specal tool to hold the pully but I have not found one thats cheap so I have used the screwdriver. and use a torq wrench to get it right.
speeddemon145 is offline  
post #8 of 15 (permalink) Old 08-16-2006, 12:36 PM
Senior
 
Join Date: Jun 2006
Posts: 500
Send a message via Yahoo to conanofcimmeria
try the locked in gear with the brakes on method.it takes 2 people but usually works.normally I find that using a mallet on a short ratchet works with a bit of loctite.best bet for proper torques is to lock the crank such as the brakes like i said
conanofcimmeria is offline  
post #9 of 15 (permalink) Old 08-17-2006, 02:22 PM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
Ok, i did everything like you both said, but now i have another problem, i check and double check the timing marks, (upper and lower crankshaft pulley - both OK).
When i started the engine the idle RPM increase form the usual 900RPM to 1000-1100RPM, the only thing i did beside the drive belt, was 4 new sparkplugs.
any idea what migth happened?
thanks

Paulo Lança
Paulo Lanca is offline  
post #10 of 15 (permalink) Old 08-17-2006, 06:38 PM
Senior
 
Join Date: Jun 2006
Posts: 500
Send a message via Yahoo to conanofcimmeria
did you disconnect the battery during this?if so the stepper motor may need resetting.other than that nothing involved in the work you did should cause it(unless you left something unplugged)spark plugs and a timing belt should be straight forward.also did you have the ignition on (listening to tunz) while you were disconnecting things?this could trip a fault code but should normally turn the eml on
conanofcimmeria is offline  
post #11 of 15 (permalink) Old 08-17-2006, 07:42 PM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
I left the battery connected during the all time, but the ignition was off.
so i just need to disconnect and connect again the battery?
I´m gonna do it
Thanks

Paulo Lança
Paulo Lanca is offline  
post #12 of 15 (permalink) Old 08-17-2006, 07:45 PM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
By the way can you explain the meaning of "turn the eml on" please?
Thanks

Paulo Lança
Paulo Lanca is offline  
post #13 of 15 (permalink) Old 08-18-2006, 07:38 PM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
Once again you saved my day, i disconnected and connected the battery, and now the idle RPM its 900.
THANKSSSSSSSSSSSSSS if you need anything form me, let me know.
Best regards

Paulo Lança
Paulo Lanca is offline  
post #14 of 15 (permalink) Old 08-21-2006, 06:12 PM
Senior
 
Join Date: Jun 2006
Posts: 500
Send a message via Yahoo to conanofcimmeria
sorry but turn the eml on refers to turning on the Engine Management Light(engine symbol on the dash) which generally means you have tripped a fault code
conanofcimmeria is offline  
post #15 of 15 (permalink) Old 08-21-2006, 07:08 PM Thread Starter
Newbie
 
Join Date: Jul 2006
Location: Portugal
Posts: 19
Thanks, lucky for me everything is ok.

Paulo Lança
Paulo Lanca is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Mitsubishi-Forums.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome