Greetings everyone. My name is Al from Perth Western Australia. I have a 1994
Triton MJ with a 2.6L Astron engine. I would like to do an engine swap to a diesel.
Will a 2.5L fit straight in and match up to the drive train, or are there mods to be done. Any help greatly appreciated.

I am constantly sick of taking a hard corner or going around a roundabout and taking them at a decent speed it will just bog down and will not regain acceleration until i straighten her up, does anyone know where and how to disable the inertia switch so that i can maintain power through the corners?

i know that the 92 TR 2.6L EFI 4g45 SOHC model is a little old yet i am planning to take the time and patience to rebuild her into a sleeper

I'm looking for a complete set of 15" GSR Pepperpot rims to buy or trade for in the Melbourne area.

If you have a set and are interested in selling, give me a call on 0405264268 or at rory.walker@gmail.com

Hey Hey everybody. This is in the Colt main section as well, but I thought because this is an Australian car and an Australian workshop I'd put it here as well.

I'm from Mild To Wild Restorations in Australia and I wanted to share with more people the Colt being released by us this week. Its just a 1988 Mitsu Colt that we have given a makeover for a radio station promotion. Its a giveaway, yep completely free to one lucky listener.

But anyway I just wanted some Mitsubishi appreciators to see this, the complete pictures will be up on the website tomorrow when we hand it over to the radio station. At the moment the complete build is there so make sure you check this out today and tomorrow.

Oh! And her names' Dolly..

http://www.mildtowildrestorations.com.au/index.php?id=228

Hope y'all dig it



For interested parties they can just checkout everything else we've done here.

http://www.mildtowildrestorations.com.au

Hi,
4G63 engine missing and stalling on hills, will run on flats.
Spent plenty trying to cure, new fuel pump, catalytic convertor, plugs, leads, air and fuel filters. Any suggestions. By the way is fuel pump in fuel tank?

Hi all

I am a new member here, and was wondering how many of you guys and girls are Aussies?

Dan

Hi,

I have a 2007 OUtlander VRX 7 seats, The 3rd row seats are just too small any suggestions if they can be replaced by a say Mazda CX9 3rd row seats which are bigger or likewise ??

Is it possible to fit gas to a Dec 06 Outlander, 2.4 litre petrol model LS auto with CVT?

regards,
Jill

hey guys
i got a pair of altezza front lights suited for a CE 97-00 for sale.
they are a pair of angel lights.
if anyones interested??

hey guys
i got a pair of altezza front lights suited for a CE 97-00 for sale.
they are a pair of angel lights.
if anyones interested??

ey guys i need sum help
im looking for a front bar for my ce coupe
probably anything close to a jetspeed r34 style
id really apprieciate if u guys helpd
thnx guys n girls tc

[B][FONT=Arial][SIZE=7] Hey all, I have a mitsubishi lancer MR 99 CE and have been fitted with Super low king springs and am willing to do a free swap for anyone who has low's. my mechanic will do the swap. anyone interested please call me or reply to this.

cheers
Simon
0433016819

I am about to have standard rear parking sensors fitted to my 06 LS Outlander 2.4 litre 4x4 auto with CVT.

Is is possible to fit another set of these as front parking sensors as well as having the rear sensors?

regtards,
Jill

I would be interested to lear of real world experiences in fuel consumption for city and rural driving for an Outlander 2.4 litre auto with CVT

regards to all,
Jill

Does anybody know of a RWD transmission that will bolt to the 3.5 ltr 6g74 engine as I would like to use one in my 1960's custom. Any help would be appreciated

G'day all, New to the Mitsubishi world but not new to 4b's. had a couple of Lux's and if want to class a WRX as a 4wd even thou it's a awd, one of them as well. I have recently purchased V6 Triton double cab and are stoked about it. It's a 98, has a few K's but after a new clutch, runs a dream....

Many Aussies on this forum????

Does anyone know if a streering rack for a 1993 nimbus can be refurbished or replaced with one out of another model Mitsubishi or are they peculiar to the UF Nimbus

Hi all.

My names Robert McGuire.

I'm interested in starting a Lancer club based in and around Brisbane.
I personally live in Ipswich but will include all of SEQ.

Going to start working on a website: www.SEQLC.com

It will be a club to have fun in. Going out on tours once a month.

I'd like to know what others think.
If anyone would be interested drop me an email at:
vision_mcr0t@hotmail.com

Cheers

- Rob.

[B]I have a 93 Verada which goes from 1st gear to third gear missing 2nd all together. I have been to a auto mechanic and he reckons a band has broken and the transmissions needs to be pulled and reconditioned.

Could it be electrical or a computer problems, I think this guy just wants the money.

Any ideas???

I have a TP Magna which has been smashed, It's motor / Gearbox unit has only 134K, interior and some panels are good, anybody interested? SE Queensland, ( Toogoolawah ) Davo

hi and i hope someone can help me here.I just got the head of my 84 pajero (2.6lt astron leaded motor) done up and have lined up all the timing marks as it was when it was taken off the car but can-not get it to run.it will fire up under acceleration but starts to backfire through the carby. so if there is anyone with any ideas it would be great.. thanking -you Pete..

Hi everyone. I live in brisbane and im looking for a speedometer for a 1985 rc colt. I tired the wreckers but they're not in to good a condition. Does anyone know the part number or where to find one. Thanks

heres the story.... well i was in the passenger seat drunk as hell after this party...so i let my friend drive me back to his... while driving home my friend said grab a better cd and chuck it in... so i took out the cd and put a new one in .... or so i thought i did this three times... theres a small gap on the top of the cd player that only just could fit a cd into it... and i managed to do it seemlessly with out vision lol....

neways the next morin after sobering up... i managed to pull the dash off to take the cd player out... to get the cds out... neways when doing this i found a auxillary cord curled up at the back.... so i grabed an extension and wired it up into the ashtray... just so u couldent see it when not in use....

i was amazed.... what was a $50 EXTRA was a quick and easy job..

also i adjusted the cd player up so there wont be any more lost CDs...

also it sounds really guud... beats the guud ol FM transmitter...

peace...

Does anyone have a manual covering a 91 diesel triton, mainly gearbox. I need to buy, download or borrow one. I live in SE Queensland. Davo757

im spendin 10000 on my 2007 lancer wat should i do i was considering 18s... already got an exhaust on it..

considering short ram....

wat else ..

gunna do tha stereo.... with all pioneer ***...

neways hit us back wid some ideas

Babes driving a done up lancer has 2 be one of the hottest sights around!

Any aus girls got nice Lancer's? Post here.

Hi guys,

just wondering if anyone knows where to get some mods for the 2007 4g69 Lancer.
I have found a lot of american sites where i can order stuff in but I want someone locally. I found RPW in perth but they don't seem to stock a nice one like the AEM's or Injen etc. The american mods would probably work but I'm not sure if the engine bay of the USA Ralliart (same engine) is laid out the same way. Any help would be much appreciated.

Cheers

Hi Guys,

If your looking to purchase some Genuine Mitsubishi Lancer Accessories from Australia, here are the links:

Australian 2008 Lancer Website:
http://www.mitsubishi-motors.com.au/#/web/...?vehicle=lancer

Australian 2008 Lancer Accessory Website:
http://www.mitsubishi-motors.com.au/#/web/...&vehicle=lancer

These parts are in Australian Dollars = US $ 0.88 per AUS $ 1.00.
There is also an additional 10% GST on all parts.

Some general (RRP) pricing on Mitsubishi Genuine Parts so far:

Clear Bonnet Protector ..... AUS $ 75.90 + 10% GST

Black Vinyl Front Ascent ...... AUS $ 50.05 + 10% GST

2 x Black Side Air Dam Ascents ..... AUS $ 80.85 + 10% GST

2 x Black Rear Wing Ascents ...... AUS $ 48.50 + 10% GST

Sports Gear Shift "AUTO" Knob ..... AUS $ 295.00 + 10% GST

Rear Park Assist .... AUS $ 482.35 + 10%

Plastic Boot Liner ..... AUS $ 67.00 + 10% GST

Tow Bar Package .... AUS $ 666.00 + 10% GST

4 x Carpet Floor Mats ..... AUS $ 100.00 + 10% GST

2 x Fog Lamps ...... AUS $ 490.00 + 10% GST

As you can see, only having a small population in Australia (20 million), parts are a little on the expensive side.

Warren

............................................................................................................

AUSTRALIAN MITSUBISHI DEALER

Contact:

Brett (Parts Manager)
Mitsubishi Parts
Alan Mance Mitsubishi
2 Holland Drive
Melton VIC 3337
Australia

Facsimile: 61-3-99711101

..............................................................................................................

AUSTRALIAN 2008 LANCER CATOLGUES (incl seperate Parts Catolgue)

If your interested, I can obtain new Australian 2008 Mitsubishi Lancer catolgues and Australian 2008 Mitsubishi Lancer Accesssory catolgues and have them posted to the USA.

At this stage I have no idea of postage costs to the USA.

1991 magna tr manual (australian model) 4 cylinder- I have owned this baby for 4 years and am looking at replacing the ecu (engine control unit? computer) for the second time. It cost me $700 last time. I was specifically told that the warranty was for 12 months- and it probably lasted 2 years.

Is there anything that makes these things screw up?

Without a repair manual or removing the unit, how do I determine the part number?

ebay has these for sale for around $150 (reconditioned)
MITSUBISHI MAGNA TR 4 CYLINDER.

ENGINE COMPUTER MODULE / ECU.

*
The Module has been Professionally Reconditioned.
*
The Module comes with a 12 Month Warranty.
*
Module Part Numbers:

BOSCH: 9.260.060.046 / MITSUBISHI: AW335189

Will these fit my TR?

Help please.

Just wondering if anyone knows some good websites or places that sell lancer body kits (i own an 01 model). I'm currently looking at this site:
GT Auto Style

Although they have a limited range, also what are your thoughts on these products, and how much (roughly) would it cost to get them painted. (I know its hard to assume without knowing details etc, just a price range)

Also i'm looking for an exhaust (muffler and tip only as i'll only be on my P's) and a nice set of wheels (also once i get pics of my car i'll ask for suggestions as crome is a bad idea in my area, because if they chip they're apparently gonna rust alot)

Thanks heaps guys

Ive got a V6 TS magna auto
It is showing a error code 63 for the trans
In the workshop manual it says the error is described as
"short -circuited torque reduction execution signal line"
The remedy is to
"check torque reduction execution signal line"
Im not sure what they are referring to? I checked the solenoids and they check out ok.
Is it referring to electrical problem or in the electronic circuitry?
Any ideas?
The symptom is when driving and coming to stop it feels like ive been shunted from behind but it only does it when it has overdrive engaged, But having overdrive engaged is for normal driving which makes it a pain.
thanks

hi guys, i am from the caribbean islands and have a lancer that i believe isa japanese
spec lancer, have you guys ever seen this in australia? as far as i know its a 4g15 Dohc
16 engine.i am looking for some projector headlighs and aasscesories for this car, can someone point me in the right direction please?i have included some pics

hi guys
im hunting for 4G32 chain drive cylinder heads, the engines were in lancer and galant models in the 70's and believe they were also called a saturn motor.
im in melbourne but also have relatives in north east victoria.
any help is much appreciated

Hello im new the the forum.

i just brought a 1994 Mitsubishi Galant HJ Hatchback Auto on tuesday and it didnt come with a manual, the dealer said that if it was in the glove box then it didnt have one to start with so im looking for a pdf version if anyone has it


Thank you for your time


Sousuke

Hi All,

i was wondering is it better to use a twin point spark plug or quad, and why?

I tried google but i have been getting just fact and outlets info (nothing really detailed other than the normal information for selling)

I own a 1990 Pajero Wagan, V6 3.0L

Thanks

Hi everyone!

My dearest 1999 MK dual cab Triton just got rolled over. It is very heart-breaking since I got it only 2 months ago.

I wonder if anyone can help me by suggesting an inexpensive way to restore it. The damaged parts are:
- smashed roof
- smashed guards
- windscreens and windows
- deformed bonnet.

The guy from smash repairs said it might be very expensive if I want him to restore it. So, I was thinking to get secondhand or aftermarket part. Anyone knows someone wrecking their Triton/ auto-wrecker / parts supplier that keep mitsubishi/ Triton stocks? would be great if they are in QLD.

Thanks for your help!!!

Cheers,

Eric

Please Help my 1991 TR Magna has the shakes when i put it in drive????

Attention Aussie 3000GT/GTO owners.......

I have a Torque Plate for hire for those doing rebuilds. It is a very good idea to use these when boring out those cylinders. PM me for details on how much.







"Lightweight block castings have become very prevalent in our market. Since the overall mass has been reduced, the controlled stresses have become an important factor in the block's integrity. To ensure integrity, we must recreate that stress by using a Torque Plate when boring and honing.

Always begin by torquing your main caps in place to correct specifications. Next, install a torque plate and torque in place using final assembly torque specifications. Also, we recommend using correct length bolts. If they are too long or too short, they may abnormally stress the block. The future will even dictate correctly torquing all external motor mounts and related accessory brackets.

Allow .003" minimum material in the cylinder bore. Remove broken and partially severed material by honing after the boring operation".

Scotty