i have a 96 4d56 non turbo and i just bought a turbo for it all manifolds etc But it never came with oil feed lines etc basically just need to find out where the numbers that are labeled go too ? and also have an intercooler as its a pajero turbo manifold etc so can i block off the intercooler for now as i'll mount that at a later date ? i'll post a picture

i need to know...

hi guys!

one question, is it feasible to make my 1992 4x2 L200 have a CRDI injection without too much work with the engine? im a newbie here so i am in need of professional help.
thnx default/' '' />

I'm a Newbie to this forum. Any help would be sincerely appreciated. I have a 1985 Mighty Max with the 2.0L engine. It's been such a good truck that I don't want to get rid of it. Recently it started smoking. I tested the compression. To my relief, the compression is good in all cylinders. I took my truck to a friend of mine who is a mechanic to get his opinion. He says he has...

hi, can anyone point me in the right direction. my problem is there is very little oil getting to the turbo and this has caused the turbo to fail. the engine has only done 26000 miles, the feed pipe to the turbo is clear, the oil pressure light goes out while cranking the engine, the oil and filter have been replaced,(10/40 semi synthetic), i have just removed the sump to check for blockages in...

Hi guys,

I have just purchased a Mitsubishi L200, it has a double cab. Thats all I know. I do not know what it is. I have telephoned Mitsubishi and they say it must be imported as we have no records of it. No matches to chasis number or registration plate.

I want to know if it is an Animal/ Warrior or other. I cant seem to tell the difference.
I really need to know...

Hello ,

does anyone know where i can get a Service Manual for a L200 Model 2004 Storm EVO
i also need a Wiring Diagram/Description or Pinout from the ECU and MUT II ODB Plug.

the normal Manual for L200 is fine but do not fit exactly for my Model.

i also looking for a Wire where i can use for Diagnostic Programs like Evoscan.

i have a Make/Model:...

I have a 1994 2-5 TD, when i first start it in the morning i have to wait a few moments before i can drive away as the steering wheel does not want to move, all of a sudden it frees itself and is fine, also there is a grinding noise on full lock which seems to ease when the cars warmed up, have checked belts and fluids , they are fine..... anyone????


Thanks in advance

I've looked around for ages for some clear taillights for my 1988 MF Triton (Mighty Max/L200), which is basically the same car from 1987-1996 (ME-MJ) with no luck. I can find the stock assembly as well as the stock lense replacements (ie. amber, red and clear lense) but would like clear lenses to change the look of my rear end (the car's Laughing ). Anyone come across some clear lenses...

Hi,
I'm having some problems that I can't seem to just identify? I've read the forum posts regarding similair issues but i'm either non the wiser or perhaps i can't accept some of the answers, any help or pointers would really be much appreciated!

I have a L200 - Single Cab 1998 2.5 TD

I have a full service history and carry out regular...

just a quick question, im looking at replacing the tray on my 96 triton with a styleside tub, but havnt been able to find any single cab tritons that had a styleside tub, so basically what im asking is, do they exsist? or is it only available with club cabs?

or if anyone knows any other way i can get a tub to fit on my ute, i'd love to hear it.

Hi everyone. Hoping someone out there can tell me roughly what they paid for a clutch kit to be done in a 3.0L V6 Mitsubishi triton. Got mine in at the shop at the moment waiting for a quote.

started slipping a bit, although not always. Car has done about 220,000Kms and I can only assume it's never been replaced.

Any other thoughts appreciated.

Thanks,

Hi
Can anyone tell me how to reset the SRS light on my 2007 mitsubishi triton? I installed a new stero and left the red/yellow connector in the glovebox off when I turned it back on. ECU did a system check and flagged it up as a fualt bringing red light on. I have plugged the connector back together but the light stays on. any help would be appreciated.. THANKS!!!

Anyone know how to remove the headunit from the L200

Also, any tips on fitting a subwoofer in there?

Cheers
Sam

Hello. My 2003 L200 is Overheating. Just had new head gasket fitted. Head skimmed and tested with no cracks. New timing belt fitted and balancing belt, New water pump and new cap fitted. Starts and drives no problem. No real overheat while driving short distance. On my way to work this morning after an hour of motorway driving the needle started to creep up but not into the red.

After...

Hi,

I bought the mitsubishi's kit for my L200, 1999 (model K74T). The kit also works on a Pajero Sport. The kit's reference is MZ312043. I successfully installed in a wiring. I tested with remote controls, and this was only the flashing light up (the warning), the doors of not moving. With the key that did not work either. I then moved the switch on the box 'on' and I...

I have a 4 Door Colt 2800 TDI and I am looking for the Mitsubishi L200 Electrical Wiring PHTE9601 OR equivalent

When I try to put shifter into H-4 or L4 it makes noise as though it is not engaging properly.

Ihave a new Triton GLX-R Manual Diesel. It shudders off the line in 1st between 1800 and 2000 rpm. Mitsubishi have told me it's normal and a characteristic of the vehicle and as such will not fix it !!!!! - The car I test drove did NOT shudder - I would not have bought one if it had or if I was aware of it.. Has anyone else experienced this and anyone know of the cause. I...

default/00000732.gif' '00000732.gif' /> just joined today, do you know if drive belt snaps is it possible to still drive the vehicle. The timing belt is still intact and there appears to be no damage to engine. Does this seem right?

Hi all!

Just wanted to pick your brains quickly. The clutch on my L200 started slipping today and it obviously needs replacing - but how much am i likely to pay for this at a Mitsubishi dealer? Is it wise to let a non Mitsubishi garage do the work?

Thanks.

1997 V6 Triton has developed an intermittant miss under accelleration.
Miss occurs when engine is operating in the 1000 to 2000 RPM range only and seems to be more noticeable when pulling out of corners.
Anyone have any ideas on cause and solution.
I have fitted new plugs and tested all leads.

It's getting cold and my heater is barely blowing warm air. I just put in more coolant but I'd like to change out the thermostat also. Problem is...I can't find it and my owner's manual doesn't show where it is.

Can anyone help?

Hi all.

Wonder if any help can be found here (my first post!).

I own a new L200 Animal 07 (had it for 2 months) & had it fitted with a Roll n Lock. Every time it rains it leaks on both the drivers & passengers side at the tailgate. I know these things are not completly waterproof, but the leak is really bad meaning I cannot store ANYTHING in the boot (water may be...

Hey all,

I would like to get a spare set of keys for my L200 but need to know how to program the chip in the new key and the remote. Anybody got any ideas?

I have just had my L200 booked in for a service at the Mitsubishi Dealers in Aylesbury and was a little shocked at the standard price.

Does anyone know what they actually do on the 81K mile service, because the receptionist could only quote me an oil change and a few visual checks!?!?!?! Are they serious for this kind of cash?

Thanks all.

Hi, having a few issues with my 2002 L200 double cab, we seem to be taking air into the fuel system somewhere, causing the engine to "misfire" occasionally, could this be linked with some poor diesel that we picked up (lots of water) which caused the engine light to come on, draining the fuel filter always cured that problem, but this has been going on for 4 months now. dealer put...

oil change and bes oil and what filters to change

Ok i have a 94 mistubishi mighty max, and it would take about 15 min for the engine to warm up (till it blows somewhat hot air outta the vents) So of course I suspected a stuck open thermostat. Got a new one and a new gasket for the water outlet. There were no coolant leaks prior to this. I disconnected the coolant temp sensor from the thermostat housing. Took off the 2 bolts holding the...

I have a 1995 Strada and cant figure the spare wheel configuration out, it seems to be just hanging on a piece of chain and is not fixed anywhere so the wheel just moves around with the motion. There is a lever that sits above it but doesn't seem to do anything as it doesn't move, have tried pulling the chain in both directions but no joy.

Thanks in advance

SB.

I’ve bought a brand new L200 animal (165ps) and i've done 2000 miles, I then purchased a common rail tuning chip from 'Diesel tuner’ (http://dieseltuner.co.uk/)
This should make it around 205ps...

Its goes really well, loads of low down pulling power / torque.

however once its been driving for about 15 - 20 minutes the engine shuts down when im in the higher...

Hi, can anyone tell me the difference between a 2004 L200 warrior and animal? Which one is actually the higher spec. My 04 animal has leather seats / air con etc but has two tone colour blue over silver and the wheels appear smaller than a warrior? Some one also told me that only the animal had abs brakes?

The person I bought this vehical from told me that it came with the the 134bhp...

I have a 1998 L200 when key is switched on the heater light comes on and goes off shortly the engine starts properly usuall i hear a relay "click" a few seconds later, recently,sometimes, at randon intervals I hear several clicks .Can any one help?

Hi All,

My Fisrt day at this Forum.

I have a 1999 L200 4Life 2.5 Turbo Diesel.

I have always had this problem with it starting when it is cold. The problem is more worse when the Weather is Cold.

I have to keep letting the glow light come up and then try start and somtimes this can take over 10 tries, and then you have to keep trying to turn the...

As the title says, Whats the difference? as ive just bought an 04 L200 animal double cab and just seen a crew cab for sale for a grand less. Same miles, year etc.

hey guys, ive got a 96 triton and am getting bored of the yellowish white lights on the taco and such and was wondering if theres a way to replace them with blue leds?

or am i out of luck

cheers
dean

hi, looking for a 12 volt constant and 12 volt switched feeds for a for a gps install in a 2005 L200, tia for info/colours default/' '' />

hey all, I've just done the intro thing but I thought I'd come in here and say hi.

I bought a ML Triton GLX-R Di-D just over a montha go and just love it.

Doing some add ons,

ARB Delux bar, colour coded
ARB Rear Bar colour coded
Warn XD9000 winch
Lightforce 240 Blitz spotties
Uniden UH015SX with GME AE4705 1.2m 4.5Db Aerial

Well kinda... I live in the USA and I am a huge Mitsu fan. I am 20 years old and in college. As soon as I get done I plan on buying a lancer for gas and for and for fun. I grew up with a 1988 Mighty max 2.0 2wd that my dad had bought brand new in 88. When I started driving they sold it and gave me a ford ranger b/c it had airbags and they wanted me to have airbags. Well now ive been driving...

Hi guys. I have a Mitsubishi triton 2007 GLS double cab. default/57.gif' '57.gif' />

Can anyone help me choose a good and powerful subwoofer that would fit at the back of the rear seat. default/' ...

Hello.

I am wondering if anyone can help me out here.

I need to replace a seat belt in a 1993 Mighty Max and I am wondering if there might be instructions posted anywhere.

The dealer wants almost $250 just for the part. I found this...

and was thinking about getting it but I don't know how difficult these things are to replace.

Any...

Hi all,

Will buy a L200 shortly in Jordan. They have never heard of the Ralliart upgrade and will not supply it. No problem to buy it elsewhere.
I checked with Mits in Holland/Europe and they were not sure if it would work because of possible interference with the motor management system. Most likely the safest answer for them, since they have never tested it.

What is...

Hi I am looking for a L200 Warrior and have been offerd a 53 plate 2.8 automatic black with grey leather 31000 miles on it and it has a windowed back on it. I have tried looking around for a comparible model but Im struggling to find another 2.8 auto. Are these imports or something or just rare cars. Can you seasoned Mitso owners help me out and what is it worth roughly.
Thanks
Peter

i am new here how is everyone
i took a wrecked 93 (flipped) and a great 90 donor and made me a nice truck
90 was 5 speed plain jane now is a 93 auto,air,ps,cd,all the plastic int,
i have for sale the 90 block and rotating assm. 5 speed tranny, wire harness and misc,
i have 93 good rolling chassis some int, bench seat needs covering, 300 dollars buys it all and could...

gyday all,im a newbie to this forum so go easy, my question to all you knowledgeable folk is how do you fit a Magna EFI system into a carby fed triton ute? Step by Step would be appreciated or if anyone has any links

cheers and thanks in advance

ollie default/beer.gif' 'beer.gif'...

Ok, point me to the right place. BTW, What engines are swappable without modifications to engine harnasses, whats a great, powerful swap that won't require extreme mods?

default/beer.gif' 'beer.gif' /> hi guys im the new fng and have a couple ?s about the reliablity of 93 mitsu mighty max pickup? down sides ? before i do something stoopid like a 12a rotary swap, or even worse a v 6 or 8 or maybe even an iron duke! what kind of aftermarket support? [ if...

2004 L200 2.5 Turbo Diesel

Just fitted a new head after head gasket problem. Set it all up - fires up no problem, idles perfect however missfires @ 1500rpm upwards.

Checked all vaccums, connections, valve clerances, etc.

any thoughts or suggestions??

Hello everyone,
I am new to the forum and to Mitsubishi's in general. I bought a 93 Might Max that has some engine trouble. I pulled the engine and took the block, crank, and connecting rods to a auto machine shop. They advised me that the block was in good shape but the crank and rods were beyond reworking. After calculating how much it will cost to get this engine running I have...

hi guys, hope you can help me?

i have got a 98 4wd l200 single cab and on friday it died and started to run in idle mode?

i had filled it up with bio diesel but i have also been running it with bio for over 4 months?.........perhaps it was a coincidence it broke down after filling it up?

anyway...... before i drained the tank i ran a pipe with clean white diesel...

i have a 1987 mighty max with a 91 2.4L 4G64 swapped motor
take into acount this is the 2.4L 4G64
which basically is a bored over 2.0L
i know that a 1st gen 4g63 eclipse head swaps on fine
are there others such as the evo heads that will work?
as i would like to turbo my mighty and make it DOHC

i did read a topic on here about the eclipses and evo motors...