can anyone help,the green economy light has stopped working on my 2000 1800cc Pinin gdi.It had a new Cat about 6 months ago,everthing was ok after that,any ideas.Oxygen sensor perhaps?Thankyou.

Failed WOF for excessive exhaust smoke. Possible causes?

I'm about to load this engine bay up with batteries but I'm stuck if I can find the "GVWR" (maximum loaded weight) of my 1987 Mitsubishi Tredia:

As you can see, the battery racks are installed in front of and behind the electric motor and the total weight of batteries in the front will be 115Kg (262 lbs).
I shouldn't be exceeding the max weight of the axles with this but I'd still like to know just what the GVWR is for the Mitsubishi Tredia. Even the GVWR for the Cordia would work - they're almost identical.
Anyone know where to look on the net?


Cheers!

I rebuilt a Solex Mikuni carb on a 1980 Dodge D50. Did this about 6 years ago with no problems. Now there isn't any gas getting to the barrells. There is gas getting to the bowl but that's it. In rebuilding could I have put a diaphram in backward and if so which one would it be? What gets the gas from the bowl to the barrells? Any help is greatly appreciated!!

The original steering wheel on my 1995 Mighty Max had been replaced with an aftermarket steering wheel and the horn was left unhooked. After removing the steering wheel, there was only one wire visible, a black ground wire. What do I need to do to get the horn working again?

I AM HOPING THAT THIS ? CAN BE ANSWERED HERE OR THAT SOMEONE WILL POINT ME IN THE RIGHT DIRECTION. I JUST PURCHASED 1997 MITSUBISHI FUSO DIESEL AND THE TRANSMISSION WONT SHIFT UNLESS I LET OFF THE ACCELERATOR OR PUSH IT TO THE FLOOR ANY GUESSES THANKS TO ALL THAT REPLY

Can any one help me with a wiring diagram on a Tredia turbo?
Engine code is 4g62. The Fuel Injection system has only 2 injectors. What is the capasity of those injectors and how do you messure it?

Thanx.... anyone.

Hi everyone,
i own 1985 dodge ram 50 sport 2.0 L. the car seems to be running alright other than a few carburetor issues. The choke takes a while to open up in the morning and then remains open afterwards. i have tried spraying carb cleaner on it several times but it has not seemed to help much.
Also the car will not stop right when i turn the ignition off. it goes through a couple more cycles then sputters out.
Lastly the car sometimes hesitates when i step on the gas from a halt, as if it were about to stall out.
Any insight into the problem would be greatly appreciated as i am not very experienced with cars and dont have money to go to a mechanic. thanks a lot!

Hi Everyone, this is my first post even though I've had 5 mitsubishis over the years gone by. I should have been a member long ago!

I'm currently converting a 1987 Mitsubishi Tredia to run on electricity but I've found the gearbox has a little bit of a major hole in it.
Does anyone know if the Cordia gearbox (supershift or not, doesn't matter) will fit this model?
I assume the gearboxes should be the same as they're cousin cars.

The car in question is at my electric vehicle conversion website www.KiwiEV.com

Thanks and gidday from downunder everyone!

Could anyone tell me what the gear ratios are for a 5-speed Cordia or Tredia gearbox? Perhaps a Starion or Eterna/Sigma gearbox is the same too?

If you have a detailed owners manual or "Haynes" manual then it should have it in there!

If you can help, I'm after:

1st Gear Ratio................... ? :1
2nd Gear Ratio.................. ? :1
3rd Gear Ratio................... ? :1
4th Gear Ratio................... ? :1
5th Gear Ratio................... ? :1
Reverse Gear Ratio............ ? :1
Final Drive Ratio................. ? :1

This will help me ascertain what RPM my electric motor will be doing in each gear at a given speed.

For those of you scratching your heads this is part of an electric car conversion. I'm sure you're all sick of me saying that but it saves me answering any "why do you want to know?" questions.


Thanks folks!

www.KiwiEV.com

What is Mitsu' Model????

http://www.powerdrive.co.th/mitsu_champ/fo...indpost&p=10588

i found it in
http://www.e-guide.ne.jp/1999/befor90/before90.htm
and in Ralliart Journal Vol. 1 Page 2
http://www.powerdrive.co.th/mitsu_champ/fo...p=943&#entry943

i want to find for more information & photo

who can help me?

thank you

on the passager side front electric window, it's go's down ok but it won't go back up until i turn the ignition off and then back on. it then go's up no problem. any advice would be great

Hi guyz am trying to change my Mitsubishi Celeste' engine.
What kind of engine should i go for?
Am kinda stuck HELP!!

Ok.. I am need of some serious help.. I currently bought a 1989 Ram 50 with the 2.6 G54B motor, 5 speed 4x4.. I took the old carb off and replaced it with a new head , 38/38 weber, flowmaster exhaust, and performance cam. The truck ran great with the new head except for the fact that oil pumped out of the breather on the back of the valve cover.. The PCV valve works and is also brand new along with the oxygen sensor.. I took the cam out and put a stock cam in the truck but the tail shaft on the cam was too long and stuck out the back ( probably a cam for a front wheel drive 2.6) so to make it fit inside the head so I could use my cam plug, I had it cut down to the size that fits in the truck version and the motor runs rough.. The whole entire truck shakes at idle really horrible when cold but no so bad when it is warm. When I drive down the road, the truck runs perfect.. What is wrong ? If anything, I would like to know how I fix the oil from coming out of the back so I can run my bigger cam.. anything would help.. Thanks

Ryan

I have a 1994 Pajero with no turn lights. i checked the fuses and they are all good ..... any help ?

my mitsy died rac recovered it to garage wher it spent 2 days being checked out then
it was put on a computer, the throttle body had burnt out mitsey quoted £1200 for new one + fitting
and secondhand ones are £300-£600 but was it worth fixing for that sort of money or do i scrap it
but i have found a place on the net that does remanufactured ones with a 2 yr no quibble no hassle unlimited miliage warranty for only £210 including vat +£8.50p P&P in u.k click on link below for all mitsey models parts cheap www.ecu-testing.com CHECK IT OUTwhat have you got to lose ? no more mitsey ripoffs
if they dont have your part send them your old one and they do it for free
let everyone know if you can they are based in derbyshire they do all makes and models
and ship world wide telphone no's are : 0115 9190770

Mob: 07971468585

regards jim

hi,


i am jm from the philippines. i am just wondering if you have a relay diagram for headlights. i recently installed a 100/90 watts headlamp, the service advisors of mitsubishi told me to put to more relays for the low beam and high beam. but there's one problem, i don't know what's the positive and the negative wires on my headlamp. my wagon is a mitsubishi adventure super sport 2.0g (4g63 - manual). it seems that the headlight is harnessing its ground from the switch. please help. jmcast2003@yahoo.com. can you guys give me a diagram? by the way the color of the wires are red blue on the left, red white on the center and red on the right socket. also, can you give me a diagram for the dimmer passing switch? thanks in advance.

[attachmentid=3856]
I've got this J26 4WD "Jeep" built in 1975 and imported then sold by Colt UK 1980 (I'm 3rd owner from new).
I am looking to replace a blown cylider head gasket but the local Mitsubishi dealer is having problems finding the correct part number (even though the vehicle is in their service bay).
The engine is a 2.6 litre Astron - which I think are being remanufactured by Mitsubishi Australia?
Can anyone help me please?
Kind regards
Bernard

Hi,

I am from malaysia.

This is first time come this forum.

Hope can be friend with all eterna member.

At malaysia, Mitsubishi eterna = Proton Perdana ( national car )

Hope can exchange all info about eterna. Hope eterna member can join together.

Hi. I have recently borrowed a car from my brother that was in the shed for some time. I have managed to get the car running and idling but when i try to drive it it craps itself. When i put my foot on the accelerator the engine dies but doesnt stall. It also pops from the air filter. Help anyone.... Thanks

I have a 91 Mitsubishi Eclipse GSX Turbo AWD and it will start but wont stay running if someone had some advice so i could get it fixed i would appriciate it.
Oh and it is an electrical problem and if i dont take the battery cables off at night then the battery will be sucked dry.

Does anyone have a copy of the workshop manual for 94 v3000?

I need the wiring diagrams so if you could scan and email or photocopy and post I'll hook you up with $10.

Ok, my friend is going to put a 354 in his monte carlo ss for christmas. he said he would give me his old engine(305 v8) would that fit in my mirage, cu zif so that would be ******* awesome! if it can im guessing i would needa new transmission..if anything else or if impossible please let me know.

wats good yall! i was wondering if any 1 knows about the instrument lights bc my out side lights work but the instrument cluster and the night alimunitation lights dont work. if u no any thing about it plz help!

I picked up a 1991 eagle 2000 gtx from a friend of a friend. The car needed some TLC and a valve job (which is now done)
Anyway. I can't seem to find any information on this car. I searched the net, but couldn't find anything. The only thing I know is that there were very few of these cars sold in Canada, and the cars counter part is a mitsubishi Gallant. Any info would be great.

i have a 2005 european colt and the dashboard always ratling. did any one has Structure manual?or any one with this proplem?

Hey y'all

I drive a 1995 Chrysler Lebaron. I know ur wonderin "why are you here?" Well, chrysler offered a 4cyl and 6cyl option with the lebaron, and the v6 they used was the mitsu-made 6g72 SOHC 3.0L. I like my car, convertibles are always fun, and it has good power and is pretty quick. I love the engine, has a nice tone to it.

Its gettin a lil worn tho, esp with how i used to run her hard. (run-in with cops changed that). ill still have some fun every now and then of course, but not too often.

Anyways, I would really love to work with this car, it has a bit of potential. I was just wondering if any of yall knew if there are any performance mods (esp exhaust/cold air) which are applicable to the 6g72 SOHC? i know the sister engine DOHC turbo powered the infamous 3000GT, so i was wondering if there might be any parts available for the SOHC model?

bought a 1994 diamante wagon cheap...runs great, in great shape. my problem is i dont have the manual...and i dont want to pay for what i need. im only looking for a diagram, or definitions of, what console indicators are for what warning. some seem vague to me...cant tell if im getting a low battery indicator meaning a new alternator. can anyone help?

can anyone tell me where the oil level warning ligth snesor is on a 1991 eci 3000 v6 shogun,not the oil pessure sensor but the level sensor,this yellow warning light comes on after about 3mins of running

greetings from a newbie. Will be spending time on this forum's past posts to get some insight into problems w/ my 93 Eagle Summit. I have had some problems lately w/ cross threaded lug nuts snapping off. The local grease cretin over worked his HD air wrench I'm sure. I have replaced 3 of the studs so far...a RPITA. Is there a source for wheel studs that are harder steel than OEM? Have some other issues but will check archives b4 bringing up a previously covered topic.
ragman

Hi all I got a Nimbus ( Space Wagon in the UK I think ) and I just stufft up my Counter Shaft Belt, got eaten by the Timing Belt. Now I can't find the Timing Marks to put it Back to getter again Can Any body Help ????? More than Happy to buy you a BEER !

entirely short of any performance but definitely an eye-catcher wherever i go! yes, this is (one of) my car!!!

MMC MINICA TOPPO the k-car!

i would like to convert my 4g92 sohc to dohc, i was wondering which dohc head that can suit the best in my 4g92 sohc.. and what others part that i need to change..
thanks

Hi guys,

this is my firsst posting, I just bought a 1985 short wheel base Pajero, due to missing, the mechanic tells me that a valve has broken or jamed,, The engine is a 4G54, is the sigma 2.6 and TE magna 2.6 are the same engine? can I replace it with the sigma or the magna head cyclinder head?


thanks

hi guys ,
I do have Dion 2.0 4G63 GDI Model. 61578Km
Car is running only with 2 cylinder, before this everty thing run good, but only the aircon gas is drain or finish.
One morning my father step on accelerator padel a little bit more(not on the move or Neutral), the the engine rpm raise up and (something wrong my father told me????), So i try to check, 'Check Engine' lights switched 'On' Idle Very low, on the first few reset have try, and now the rpm is high about 1500rpm.
1, ETV motor error code check by MUTII
2, Cylinder no.1 & 2 firing is not working

how can i overcome this problem who can give me solutions, or which website can i access to get solution on my problem

Thanks

Where can I buy tie rod boots - I hope it ´s the correct word - for my Mitsubishi Nimbus UC 1990. Mitsubishi told me my model is not any more in the computer. I Must go to Auto Barn or somewhere else. The rubber right side of the power steering is wrotten.
And remember I am living in Australia near Brisbane.

Maybe later on I ´ll have some more questions.

Thanks Herbert

Hello guys, I am going to change my original 4G32 1.6L engine carb to a Weber 32/36 one, so I need to know the best jetting for this one...

The engine is fully stock, only exhaust tubing modified and MSD ignition installed...

Thaks for your help... The car is for autocross and street use, and I don't care for gas mileage...

Hello guys, can someone help me: I need to change my rear camber adjustment of my Cordia GSL. I am using it to race autocross.

I have to modify it with something easy, I can't use any Camber/Caster aftermarket parts...

Thanks for your help...

Hi ! I am trying to find some info on this 1990 Mitsu mini - Dump Truck - its a super small vehicle - and its has a governor that allows it to only go 25 MPH.

I am trying to find out if its carburated - or TBI Injection - ans also how to adjust the governor to around 35 MPH I use it on a large farm.

Where can i find parts for this thing as well? I have done some looking on the web - but cant find out what these things are even called!

Any info or links or phone numbers would be of gret help! thanks in advance!
You may email me directly if you wish
danpayton@gmail.com
thanks!
-Dan (see picture)

[attachmentid=1544]

I rebuilt a Solex Mikuni carb on a 1980 Dodge D50. Did this about 6 years ago with no problems. Now there isn't any gas getting to the barrells. There is gas getting to the bowl but that's it. In rebuilding could I have put a diaphram in backward and if so which one would it be? In the mornings is when this happens. I can dump gas in the barrel to get it started and it will be ok the rest of the day. I can turn it off, do something, come back in a few hours and it starts right up.

Any help is greatly appreciated!!

hello one and all,
I have just recently aquired a 1998 mitusbishi express SJ MWB van. Top van, drives like a dream. Anyways, It came fitted out with an alarm/immobiliser system already installed, the thing is though that the immobiliser side of the system is not hooked up. My problem is im having a little trouble finding the fuel pump and starter motor wires to patch into the alarm system. I would have thought that they would have been located under the steering coloum which they most probably are, but there are so many wires under there im having a hard time figureing out which one is which. I wouldnt think this would be a difficult task, i would assume it would be straight forward actually. What i need is a simple wiring diagram, or an explanation of where i might find these ilusive wires. If anyone has a wiring diagram they could send me, (hewi13@hotmail.com) or has knowledge of where i might find these wires or has any advice or comments/help what so ever that would be much appreciated
thanks guys & gals
mike

Hi all,

Looking at getting a Mitsi Express for a second veichle, own a 5 litre Commodore wanting something just a bit cheaper to run around town in . I would like to put some Rims of some type on it, what are my options with the stud pattern they have? Would be great if the Mitsi's are all the same but I doubt this is the case? Vans may have their own pattern?

Looking at an early 90's model by the way.

Thanks all
James

screen freezes when turned on and all buttons not functioning:radio buttons,tape buttons and tv buttons for 2000 Mitsubishi Cedia SE-R.Does anyone have the manual for radio,tv and CD.