Welcome Guest ( Log In | Register )

Mitsubishi-Forums.com > Mitsubishi Models > Colt & Mirage Forum > Colt & Mirage
     
Mitsubishi-Forums.com - The UNOFFICIAL Mitsubishi Community This site is NOT affiliated in any way with Mitsubishi or any of it's subsidiaries. Our goal is to provide Mitsubishi owners an information outlet - a means to communicate with other Mitsubishi owners. It is simply a community where fans and owners can get the right information for tuning, customization and general discussions on anything about Mitsubishi. You'll find the answer to almost any question about your Mitsubishi in this site. If not, simply join and ask! We have many willing expert members just waiting to answer your questions.

                        
Powered By IP.Board 2.3.6 © 2008  IPS, Inc.
Mitsubishi-Forums.com is not affiliated with or endorsed by Mitsubishi Motors.
 
 Reply to this topicStart new topic

Do you like Mitsubishi-Forums.com? Link to us and help spread the word about our forum. Thanks!
> Routing Wire From Engine Comp To Cabin, Electric
blakwag
post Feb 4 2007, 11:41 AM
Post #1


Newbie


Group: Members
Posts: 13
Joined: 2-February 07
Member No.: 34,973
Status: Offline
Location: SoCal
Drives: 1998 Mirage 1.5
Hey guys, I'm installing an amp soon and was wondering what route you guys were taking to run the power cable from the batterty to the amp. I noticed a rectangular rubber grommet aroung the middle bottom of the firewall. Any ideas?

Oh, I have a 98 Mirage. TIA!
Go to the top of the page
 
QuoteReply
mittech
post Feb 4 2007, 03:28 PM
Post #2


Veteran
*****

Group: Moderator Emeritus
Posts: 1,559
Joined: 17-April 05
Member No.: 8,913
Status: Offline
Location: delaware
Drives: mitsu
The most common is the grommet that the speedo cable uses. I have also seen many people drill a hole and pass the wire through then apply sealnt around the opening.
Go to the top of the page
 
QuoteReply
blakwag
post Feb 4 2007, 06:41 PM
Post #3


Newbie


Group: Members
Posts: 13
Joined: 2-February 07
Member No.: 34,973
Status: Offline
Location: SoCal
Drives: 1998 Mirage 1.5
Thanks for the reply. Just finished and I'm pretty sure that's what I used. Finding an opening was the hardest part of the install. :wacko:
Go to the top of the page
 
QuoteReply
  Advanced Search
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

Reply to this topicStart new topic
Get your Mitsubishi listed in the Garage Today, for FREE, to share with the world what you drive and what toys and modifications you have.

Collapse

> Similar Topics

  Topic Replies Topic Starter Views Last Action
No New Posts Compression In Motor
 4 dburmeister 27 Yesterday, 12:53 AM
Last post by: dburmeister
No New Posts Engines Burning Too Rich And Almost Stalls When...
Stopping at lights car almost stalls out
 7 theericwright 237 15th November 2008 - 12:46 AM
Last post by: xwarxpigsx
No New Posts Engine Light!
 2 arnmeadows24 90 14th November 2008 - 02:13 PM
Last post by: SC-CUSTOMS
No New Posts Tons Of Starion Parts In Md...
 0 seeker 30 12th November 2008 - 07:51 PM
Last post by: seeker
No new Topic has attachmentsTook A Few Pics Today
99 Galant GTZ
 38 maximus 252 11th November 2008 - 02:05 PM
Last post by: d-monic951

 
 
 
Time is now: 22nd November 2008 - 12:25 PM
(c) 2004 Mitsubishi-Forums. All rights reserved.
Mitsubishi-Forums.com is not affiliated with or endorsed by Mitsubishi Motors.